New Country Overview

One of our own in-house styles, the new country style is our take on a traditional shaker door with the addition of a tongue and groove centre panel for added texture. Its informality makes it perfect for utility rooms or country kitchens where a relaxed atmosphere is desired. Charming when combined with tongue and groove panelling.

Technical Information

In order to give opening clearances, doors and drawer fronts are generally a little smaller than their carcases. If you are not replacing old doors (which you can measure) please study carefully the details below.

replacement mdf doors

Base units (with recessed plinths): Doors fit flush to bottom edge of carcase with the total height of door, or door and drawer(s), or set of drawers being 5mm less than the overall carcase height.

Wall units (with lighting trim & cornice): Doors are 6mm less than the overall carcase height, giving 3mm clearances both top and bottom. THE SAME FORMAT APPLIES TO ANY CUPBOARD WITH CORNICE OR SKIRTING PROJECTING FORWARD FROM THE CARCASE. Horizontal gaps between doors/drawers on the same unit should be set at 3mm each.

Single doors are 5mm less than the overall carcase width.
Double doors are each 4mm less than half the overall carcass width.

replacement mdf doors

With the exception of drawer fronts, all doors are made using 75mm rails and either 6/9/12/15mm centre panels, depending upon the style chosen. Doors over 1600mm high (1), come with a 153mm centre rail above a 700mm base panel. Please specify should you wish this rail to be at a different setting.

Drawer fronts up to 150mm (2) are solid 21mm MDF. Drawer fronts 150mm – 200mm high (3), are supplied with 50mm top and bottom rails and flat panels. All drawer fronts (and doors) over this size (4) and (5), have standard 75mm rails all round.

When ordered, are on 87mm centres (6), but can be sited in any position required. In such cases please specify the preferred position by measuring in from the top and/or bottom edge of the door to the centre of the 35mm hole. Doors over 1600 high require 3 hinges as standard. Please specify the hand of the doors on all doors over 1600 height and on any door where the hinge positions are not symmetrical. The hand of the door, denoted left (L) or right (R), is the side on which the hinge is placed when viewing the unit from the front.

When ordering hinges, specify the thickness of the carcass sides.

replacement mdf doors
JMF Doors - standard hinge positions diagram

If you require end panels, lighting trim or plinths to coordinate with your door style, contact the office with a list of the lengths you require and we will assist you further.

Get A Quote

Step 1: Input your height, width and quantity (in millimetres), then click “CALCULATE” for an instant quote which includes VAT

Step 2: Click ‘ADD TO QUOTE’ to add your item(s) to your order quotation – please repeat steps 1 & 2 for different sizes of doors

Step 3: Click ‘VIEW QUOTE’ which gives you the total value of your quotation (excluding the delivery cost) – please complete the online form thereafter, in order to receive a full quotation for your project

See the full price list by clicking here


Please add £25.00 for each £100.00 (or part thereof) to cover delivery costs, up to a maximum of £225.00. Delivery is free within 25 miles of the factory, or clients may collect free of charge.


Watch our simple video for tips on how to measure for replacement doors. There is a section at the end of the video listing all of the information covered in the video if you need to take notes.

No, however, they are spray primed with a special primer/filler and then flatted by hand, which gives the best surface upon which to paint and saves a lot of time versus doing this step by hand at home.

MDF or Medium Density Fibreboard is a fibre board made from wood fibres and resin, bonded under high pressures. The finished boards do not have a grain and are therefore ideal for painting or filling. Thus holes can be filled and sanded with ease and are completely invisible when painted- very handy should you ever decide to change from a handle to a knob, for instance.

Another advantage of MDF is that once it is sealed, it is a very stable material, and unlike wood, is not prone to warping or shrinkage- extremely important when manufacturing large wardrobe doors, most of which are over 2m high. Finally, all of our materials are sourced from manufacturers who use wood from sustainable forestation, and as the process also uses the whole tree by using the wasted branches and bark left over from larger board production, there is little wastage, making MDF doubly environmentally sound.

All of our doors are 21mm thick with a minimum 9mm panel in the centre.

Our standard rail is 75mm wide on our new and replacement kitchen cabinet doors with taller wardrobe doors featuring a 153mm wide mid or cross rail.

Yes, we regularly make angled doors. Please contact the office for details of the measurements we require.

The hinge boss hole should have a centre point. Simply measure from the top of the door to the top hinge hole centre point and then again from the top of the door to the centre point of the bottom hinge hole. Always measure from the top of the door to the centre point for all hinge positioning measurements.
The second measurement we need is from the side of the door to the hinge hole centre point. As a guide, this is usually around 21mm.

We can certainly try! Just send us a photo, one close up and any dimensions that would help us to understand the proportions of the design and we will do our best to assist.

Yes, please have a look in our accessories section on this website for a list of the sizes and prices.

Yes, please have a look in our accessories section on this website for a list of the sizes and prices.

Our chosen courier is Tuffnells and they will deliver between 8am and 6pm or you can choose an earlier delivery at a small additional charge. Large orders will be delivered by our own driver if this is a more economical way for our customer.

Yes, if you are a trade client and need to order samples to show your customers, we do offer a kit of 5 doors of your choice. Contact the office for more details. If you are a direct customer, we can sell you a small sample door. Contact the office for details.

The minimum height for a drawer front to include a panel to match a chosen door style is 200mm to allow for the size of the rails to match the doors. If the drawer front ordered is less than this, then a plain drawer front is supplied.

Yes, you can collect your doors during normal business hours.

NEED ADVICE? Call us on 0121 328 1643 or Email

We'll try our best to accommodate your specific request. You'll be surprised what our highly-skilled team can do.